SFB14 error code 8 (Access error on the partner CPU)
Gents, i'am getting error code 8 when i try to read from another plc . Both are siemens im151-8 plc's. I hope anyone can help. Regards, Mucho
View Articlewhat should i read
hi i am new to seimens ,we have s7 -300 ,anyone tell me what should i read to be good on seimens .hope to hear soon. Regards Akash
View ArticleModbus TCP/IP Communication Stop
I work with Modbus TCP/IP Communication on CPU S7-1200.I've configured MB_Server block V3.1, but after 15 min it stops. In MB_Server_DB , Static - Request_Count and Server_Message_Count stop to go up,...
View ArticleUnable to change time tables and Cycle tables in Wincc SCADA 7.2
Hi, I am unable to change cycle and time tables during runtime in SCADA , Can anyone help me out through this. Thanks.
View ArticleClik here to view.
FREE SIEMENS PLC TRAINING
Thank you for helping my channel https://www.youtube.com/channel/UChdTzYTTKTLjTBa6GK81gFw
View ArticleIEC_TEST TOOL HELP
Hi everybody. I am new in this forum, I will appreciate your help, I am an electrical engineer, currently I work with a tool called IEC TEST PROTOCOL 870 5 101, it is a freeware protocol analyzer,...
View ArticleLooking for programmer help
Hello, I am not sure if this is an appropriate place for this but we are a company that does electrical engineering for material handling systems in north Dallas, TX. We are looking for an experienced...
View ArticleSoftware for Siemens s7-1200
Hi guys, i have siemens s7-1200 that i need to communicate with. Meanwhile i have programming software Simatic Manager ver.5.3. Can i use this Simatic manager to communicate with s7-1200, and how to...
View Articlehelp regarding programming
hi i was checking program there a certain bit (q4.2) is getting ON but i cant locate the way how that bit is getting activate i tried searching in program .PLEASE tell me what can i do to check that...
View ArticleTIA Runtime takes long time when starting up with the OS system
I have a project that run WinCC in a PC that has configuration: Core i5, RAM 4GB, HDD 500GB. WinCC connected to S7-1200. I built a runtime file, and set up Autostart in WinCC RT Start. At the...
View ArticleSIEMENS S7 STATION
Dear All, I am very new to S7 PLC programming (S7 Simatic Manager v5.5) and I wanted to know how to back-up a system consisting of multiple PLC Stations (S7-1200, S7-300, etc). I am able to upload...
View ArticleAdd a DP slave in sytem ( support Redundance)
Hi everyone! I have 2 PLC 412-3H run paralle (1 Master, 1 Slave). 2 PLC connect profibus network with I/O module S7300 throught 2 IM153-2 module. I have a Getway GW-7552 (DP slave) to change profibus...
View ArticleAnalog Input reading not tally
Hi everyone, I had encountered a silly issue. There is one of S400 AI module connected to S300 AI module. After power on, the reading at PROface(S300 HMI) show half compared with SCADA WinCC(S400...
View ArticleAlarm configuration Wincc v5.0 and v7.2
Hi all, I had 2 sets of Wincc HMI, 1 is v5 and another is v7.2. In this case, is it possible to configure "alarm broadcast" to both HMI PC between v5 and v7.2 ? Alarm broadcast I meant was the when...
View Articletransfer data from visual studio to s7-300
how i can transfer data from visual studio 2010 ultimate visual basic language to variables in simatic manager siemens s7-300
View Articlehelp me
you can download vesion 4.1.2 hhelp me https://support.industry.siemens.com/cs/document/107539750/firmware-update-for-cpu-1214c-dc-dc-dc-14di-10do-2ai?dti=0&lc=en-WW
View ArticleClik here to view.
How to Scale a analog value?
hello guys....How are you all? im new to siemens plc, so i dont know how to scale analog value in STEP7 plc's? and also i dont know how to use AI,AO,DI,DO? how to address them? can anyone help me?
View ArticleS7 317-2DP Softplc Sinumerik commumications
Alight first off, I'm NOT a siemens guy, Second thanks in advance for any and all advice. So i'm working on a large data collections project, been now handed part of this project that is completely...
View ArticleClik here to view.
S7 Classic
When I browse for a project to open the S7 software takes a long time and reports it cannot find a network drive? How can I stop it looking for a network drive?
View ArticleVideojet 1620 with Siemens
Hi guys, currently working on the communication with videojet 1620 printer (Continuous Inkjet Marking), in there operators manual...
View Article