Analog Input Module
I have a Siemens 4AI xRTD 6ES7 144-4JF00-0AB0. I am looking for a infrared temperature sensor to measure temperature of parts in a cooling chamber. Is it possible to wire a sensor directly back to...
View ArticleTIA Portal V15.1
Hi I am looking to move data on a part once it has been scanned at a station. All I need to move is the 2D matrix Code and time stamp. I have moved the code and time stamp into a bufferArray I am just...
View ArticleWinCC - older version or not fully installed?
Hello, I have installed Simatic S7 5.6 and WinCC Flexible 2008 Runtime SP5 on a Windows 7 computer. Running Simatic Manager brings up the error message 'Simatic WinCC flexible - Older...
View ArticleWinCC - older version or not fully installed?
Hello, I have installed Simatic S7 5.6 and WinCC Flexible 2008 Runtime SP5 on a Windows 7 computer. Running Simatic Manager brings up the error message 'Simatic WinCC flexible - Older...
View ArticlePiD Control question
Hello, I have a function block that uses a PID control to operate a heater (actually a number of them). The engineer who wrote this is gone and I have no experience with this particular...
View ArticleS7 300 software redundancy problem
Hi dears, I did a s7 300 redundancy, change between CPUs will be done sucessfully but when cpu changed, output value of one DO module will be zero and true again. I want to know that it is possible in...
View ArticleClik here to view.
transfer graph transfer to ladder tia portal v13
Hello, Can anyone hep to convert the graph for Tia portal v13?
View Articletp1200
hello everybody ı have machıne wıth sımatıc s7-1500 wıth tp1200 comfort how can ı upload program from hmı tp 1200 comfort to my laptop wıth tıaportal v17
View Articletp1200
hello everybody ı have machıne wıth sımatıc s7-1500 wıth tp1200 comfort how can ı upload program from hmı tp 1200 comfort to my laptop wıth tıaportal v17
View ArticleSiemens hmi
Hi everybody is there anyway or a piece of software out there that allows the upload of an hmi project for editing. I need to rebuild a project. The plc and hardware side is ok. I can use prosave to...
View Articleseımens
hello everybody ı have machıne wıth sımatıc s7-1500 wıth tp1200 comfort how can ı upload program from hmı tp 1200 comfort to my laptop wıth tıaportal v17 ı dıd backup and tempt fıle but ı dont no haw...
View ArticleOnline Intro Training Course Recommendations
Old Wizard here with 36 years PLC Experience ranging from Omron, Toshiba, Ge, Mitsubishi, PLC Direct and Rockwell Automation. Have never had cause to get serious about learning/using Siemens PLC...
View ArticleClik here to view.
Data Block storage in simulation mode
Hi... Folks In DB, I have entered PV as 10, but in simulation, it's showing previous value 2 in monitor section. Why it can't able to update as 10? Whether i have to use a real hardware to achieve as...
View ArticleClik here to view.
S7 Modbus with Nicotra Gebhardt fans
A customer site has 26 Nicotra Gebhardt EC PFP roof mounted ventilation fans. Control and monitoring is to be via Modbus RTU withing a Siemens PLC. I am sequentially reading data OK from the fans with...
View ArticleProblems getting WinCC to read a Double
Dear reader, I am writing a C# program using the library ‘EasyModbus’ that needs to communicate with Siemens WinCC via the connection type ‘Modicon modbus’ I have written a version using the ‘float’...
View ArticleSimatic Step 7 v5.6
Hello, can you help me with this problem. I use Simatic Step 7 v5.6 with Starter 5.4 software and when I open project, the app show me following messages. One or more objects or a type...
View ArticleClik here to view.
Siemens et200pro fc
Hi can anyone assist me..had to replace a siemens et200pro fc and wondering g how I go about transferring parameters over from previous frequency converter.. What software do I need etc Thanks
View ArticleClik here to view.
S135U R Processor QVZ Fault
I am getting a QVZ light. I opened ISTACK but I don't really understand what it is telling me. I've attached a couple screenshots. I'd appreciate any help.
View Articlemoore mycro 352
in the user manual for mycro 352 it has different programming for function blocks that are A, B, or C ...but i am not sure where this A,B, or C comes from. it doesnt discuss in user manual or service...
View ArticlePCS7 Management Console Not Working Properly Says Must be Reinstalled when...
When installing and running SIMATIC Management Console, I am able to see all the computers on the current subnet and connected to the Management Console PC. When trying to add the Management Console...
View Article