Clik here to view.
Siemens STEP 7 V5.6
Hello, I'm pretty rusty on my STEP 7 software so looking for some help. We have FB's all written in STL. In the block interface/environment there are IN, OUT, IN-OUT, STAT & TEMP sections that...
View ArticleClik here to view.
Siemens S5-95U PLC Stops Randomly then Runs again and Battery Concern
Hi All, We have a hydraulic press that is being controlled by Siemens S5-95U PLC . Lately the S5-95U has been randomly stopping during operation thus causing the hydraulic press to stop running....
View ArticleClik here to view.
Siemens S5-95U PLC and Battery Concern
Hi All, We have a hydraulic press that is being controlled by Siemens S5-95U PLC . Lately the S5-95U has been randomly stopping during operation thus causing the hydraulic press to stop running....
View ArticleSiemens TP900 HMI - Unable to go online
Hi all, I have a vendor skid on-site with a Tp900 HMI. I am unable to go online to it. Any time i try to establish a connection i get the message: Going online: the HW configuration of the HMI_RT_1...
View Articlecalling a Cognex job with Siemens TIA V 16
I am setting up a vision inspection station which will require me to have 3 independent jobs within the camera. I am using 2 Cognex 9912, a Cognex 2000, and a S71200 PLC. Cognex has sent me a copy of...
View ArticleLogo mem card
Hello, i have one questions. Is possible upload program from SIEMENS LOGO MEMORY BATTERY CARD ? If is possible ... how? Thank you for your help. Regards Beny
View ArticleQuadriga
Hi all. does anybody on here have a working program Quadriga. If so is it able to convert to a Siemens S5 backup file for me ? any help much appreciate. regards mark
View ArticleQuadriga program
Hi all. does anybody on here have a working program Quadriga. If so is it able to convert to a Siemens S5 backup file for me ? any help much appreciate. regards mark
View ArticleComfort Panel text problem
Hi there! I have a project loaded to a TP700 Comfort Panel. I recently downloaded some modifications to it and after downloading it, the text boxes and buttons' texts have messed up. No matter what I...
View ArticleLOGO!SoftComfort - Help with Analog Instructions
Hello! I was trying to configure an Temperature Sensor using the Analog Threshold Trigger to parameters and output activation but, when I put this function on the program, there's just input point,...
View ArticleClik here to view.
LOGO!SoftComfort | Another help with analog instructions
Hello! I have a humidity sensor 0-10v and his measurepoints is for 10 to 90 humidity %. Using the Analog Amplifier, I set his measure range but theres a problem... he's only givin me integers...
View ArticleClik here to view.
TS adapter MPI/RS232 V5.2
Dear Sir,I Installed the Simatic manager S7 V5.6 SP2 on an operating system Windows 7 Professional SP1 64 bitsI used the following driver to connect with the PLC online:TS adapter MPI/RS232 V5.2 "...
View ArticleClik here to view.
HELP WITH ETHERNET COMMUNICATION LOGO8 SIEMENS AND KINCO HMI
Hello! I was trying to communicate my siemens logo with an kinco hmi but this error are appearing on the hmi, what am I doing wrong? Im using an ethernet hub! ETHERNET SETTING ON THE HMI THE PUSH...
View ArticleClik here to view.
HOW CAN I USE NETWORK I/O ON LADDER SOFTCOMFORT?
Hi! I was doing an project using function block, but at one point it became too complex to use FBD so I would like to use ladder. I'm using an ihm and that's why some inputs are of the network type,...
View ArticleS7-1500 redundant CPU hardware configuration
I am building a redundant system using S7-1515R-2 CPU with TIA V16 version. Creating the hardware, there is not possible to insert any other card to the rack. Even power modules (PM) can not be...
View ArticleSinamics V20 to S71500 via RS485 (USS)
Greetings everyone, I have a TIA V16 project in which I set up 7 drives to communicate with an S7 1500 controller via RS485 using USS protocol. The drives are Simatic V20s daisychained to the bus and...
View Articleop320-a communication
Hi, I have a plc s7-200 (224xp) and a hmi op320-a, made the programs and download both, but the hmi don't connect with plc. the cable is correct like manual (op side pins 1-9 to plc pin 3, and op...
View ArticleClik here to view.
Connection problem between WinCC Explorer & Step 7 Manager
Hello, i want to create a connection between Step7 Manager and Wincc Explorer to share tags. I configured wincc to PLCSIM MPI (Create new MPI connection in Tags management) connection but when i...
View ArticleClik here to view.
Simatic Manager program issue
Hi I have had a s7 program sent to me from a machine builder that is missing the actual hardware configuration and current program file, all I get is the S7 folders from previous versions of the...
View ArticleProblema con PLCSIM v15.1
Hola chicos, necesito ayuda. Tengo problemas con PLCSIM V15.1, no arranca, parece como si entre TIA PORTAL y PLCSIM faltara comunicación o algún fallo de interface se produjera. PLCSIM aparece en...
View Article